Wheel Washers

Home Products

• Wheel Washers

Installation

If required we can offer a full on-site installation and commissioning service using our own experienced engineers. Our experienced engineers will fit the BIO-SPARGE to your concrete base, connect up to your water supply and plug in the electrics to your socket. All ground and electrical work to be completed by others. Depending on which …

→

• Wheel Washers

BIO-SPARGE 100

The Bio-Sparge SMB SH-100 is a Farm Entrance Security System designed to automatically spray vehicles entering or exiting with a water and chemical disinfectant spray to help eradicate the challenges that face farms and flocks from day to day visiting traffic, this is the most basic model that Bodo Ltd manufacture and does not come …

SERVICES REQUIRED

ELECTRICAL
230v 50Hz, 13A, Single Phase

A qualified electrician should undertake the electrical installation. All electrical components are CE Marked and the Control Cabinet wired to EN60204-1.

Note: We recommend that an RCD is fitted to the Electrical supply to the Bio-Sparge SMB. General use: 30mA 20 millisecond, Equine, Racehorse installations: 30mA 5 millisecond.
WATER
We recommend an IBC (Intermediate bulk container) which has the capacity of 1000 ltrs of water/chemical mix, supplied by yourselves.
CHEMICAL / DETERGENT
It is recommended that a biodegradable PH neutral Chemical / Disinfectant is used with the Bio-Sparge SMB.

Consult with your chemical supplier and ensure that the chemicals used comply with all regulations and local bylaws.
CONCRETE BASE
The system needs to be mounted on a concrete base with all of its counter parts (sensor posts, spray bars, main unit etc).

→

• Wheel Washers

Bio-Sparge Extras

BIO – SPARGE SMB – SH (240 volt supply) The Bio-Sparge SMB – SH is a Farm Entrance Security System designed to automatically spray vehicles entering or exiting with a water and chemical disinfectant spray to help eradicate the challenges that face farms and flocks from day to day visiting traffic, this is the most …

→

• Wheel Washers

BIO-SPARGE SMB 160

BIO-SPARGE SMB 160 (240 volt supply) The Bio-Sparge SMB 160 is our second largest version which covers larger roadways and heavier traffic coming onto site. The Bio-Sparge SMB is a Farm Entrance Security System designed to automatically spray vehicles entering or exiting with a water and chemical disinfectant spray to help eradicate the challenges that …

SERVICES REQUIRED

ELECTRICAL
380-415v, 50Hz, 3P + N + E, 16A, Three Phase Bio-Sparge Units

A qualified electrician should undertake the electrical installation. All electrical components are CE Marked and the Control Cabinet wired to EN60204-1.

Note: We recommend that an RCD is fitted to the Electrical supply to the Bio-Sparge SMB. General use: 30mA 20 millisecond, Equine, Racehorse installations: 30mA 5 millisecond.
WATER
We recommend that a tap, or isolation valve should be installed in the water supply to the Bio-Sparge Cabinet, to allow the water supply to be turned off for maintenance of the Bio- Sparge SMB.

Clean Mains water, or a Borehole water supply, minimum pressure 2 bar (29 PSI) maximum pressure 7 bar (100 PSI).

If the water supply is not clean then an inline filter should be fitted to ensure that only good quality water is supplied to the Bio-Sparge SMB.

Note: The Bio-Sparge SMB incorporates back flow protection (WRAS classification Type A Air Gap with Circular Overflow). However some Water Authorities may consider that the fitment of a reduced pressure zone valve, or other verifiable backflow prevention device for protection against backflow in fluid category 4 or 5 is necessary. If in doubt contact your local Water Authority or a qualified ACP (Institute of Plumbing & Heating Engineers Approved Contractor Person).
CHEMICAL / DETERGENT
It is recommended that a biodegradable PH neutral Chemical / Disinfectant is used with the Bio-Sparge SMB.

Consult with your chemical supplier and ensure that the chemicals used comply with all regulations and local bylaws.
CONCRETE BASE
The system needs to be mounted on a concrete base with all of its counter parts (sensor posts, spray bars, main unit etc).

→

• Wheel Washers

BIO-SPARGE SMB 120

BIO-SPARGE SMB SH (240 volt supply) The BIO-SPARGE SMB 120 is our most popular system and widely used on for farms biosecurity both in the UK and overseas. The Bio-Sparge SMB is a Farm Entrance Security System designed to automatically spray vehicles entering or exiting with a water and chemical disinfectant spray to help eradicate …

SERVICES REQUIRED

ELECTRICAL
230v 50Hz, 13A, Single Phase

A qualified electrician should undertake the electrical installation. All electrical components are CE Marked and the Control Cabinet wired to EN60204-1.

Note: We recommend that an RCD is fitted to the Electrical supply to the Bio-Sparge SMB. General use: 30mA 20 millisecond, Equine, Racehorse installations: 30mA 5 millisecond.
WATER
We recommend that a tap, or isolation valve should be installed in the water supply to the Bio-Sparge Cabinet, to allow the water supply to be turned off for maintenance of the Bio- Sparge SMB.

Clean Mains water, or a Borehole water supply, minimum pressure 2 bar (29 PSI) maximum pressure 7 bar (100 PSI).

If the water supply is not clean then an inline filter should be fitted to ensure that only good quality water is supplied to the Bio-Sparge SMB.

Note: The Bio-Sparge SMB incorporates back flow protection (WRAS classification Type A Air Gap with Circular Overflow). However some Water Authorities may consider that the fitment of a reduced pressure zone valve, or other verifiable backflow prevention device for protection against backflow in fluid category 4 or 5 is necessary. If in doubt contact your local Water Authority or a qualified ACP (Institute of Plumbing & Heating Engineers Approved Contractor Person).
CHEMICAL / DETERGENT
It is recommended that a biodegradable PH neutral Chemical / Disinfectant is used with the Bio-Sparge SMB.

Consult with your chemical supplier and ensure that the chemicals used comply with all regulations and local bylaws.
CONCRETE BASE
The system needs to be mounted on a concrete base with all of its counter parts (sensor posts, spray bars, main unit etc).

→

• Wheel Washers

BIO-SPARGE 320

BIO-SPARGE SMB-320 (415 volt supply) The BIO-SPARGE SMB-320 is our largest system and widely used for mills, abattoirs for biosecurity both in the UK and overseas. The Bio-Sparge SMB is a Farm Entrance Security System designed to automatically spray vehicles entering or exiting where the entrance and exit roadway need to be controlled separately with …

SERVICES REQUIRED

ELECTRICAL
380-415v, 50Hz, 3P + N + E, 16A, Three Phase Bio-Sparge Units

A qualified electrician should undertake the electrical installation. All electrical components are CE Marked and the Control Cabinet wired to EN60204-1.

Note: We recommend that an RCD is fitted to the Electrical supply to the Bio-Sparge SMB. General use: 30mA 20 millisecond, Equine, Racehorse installations: 30mA 5 millisecond.
WATER
We recommend that a tap, or isolation valve should be installed in the water supply to the Bio-Sparge Cabinet, to allow the water supply to be turned off for maintenance of the Bio- Sparge SMB.

Clean Mains water, or a Borehole water supply, minimum pressure 2 bar (29 PSI) maximum pressure 7 bar (100 PSI).

If the water supply is not clean then an inline filter should be fitted to ensure that only good quality water is supplied to the Bio-Sparge SMB.

Note: The Bio-Sparge SMB incorporates back flow protection (WRAS classification Type A Air Gap with Circular Overflow). However some Water Authorities may consider that the fitment of a reduced pressure zone valve, or other verifiable backflow prevention device for protection against backflow in fluid category 4 or 5 is necessary. If in doubt contact your local Water Authority or a qualified ACP (Institute of Plumbing & Heating Engineers Approved Contractor Person).
CHEMICAL / DETERGENT
It is recommended that a biodegradable PH neutral Chemical / Disinfectant is used with the Bio-Sparge SMB.

Consult with your chemical supplier and ensure that the chemicals used comply with all regulations and local bylaws.
CONCRETE BASE
The system needs to be mounted on a concrete base with all of its counter parts (sensor posts, spray bars, main unit etc).

→

Give us a call to discuss your unique requirements and we would be happy to help you with anything you need.

Get In Touch
Close Search Window
↑