SMB BIO-burbujeo 160-(400 volt Three Phase Supply)
BIO-SPARGE SMB 160 is a larger system specifically designed for larger sites
which have higher volumes of traffic / wider roadways.
biggest system comes with twin spray bars for the better coverage of a high
The Bio-Sparge SMB 160 is a Farm Entrance
Security System designed to automatically spray vehicles entering or exiting
with a water and chemical disinfectant spray to help eradicate the challenges
that face farms and flocks from day to day visiting traffic.
Inteligente movimiento de la barra (SMB) technology
automatically triggers the system (walkways can be installed with these beams
if you have a personnel walkway, so they don’t trigger the system off.).
Users can easily select vehicle spray
direction, Entry only, tanto de entrada & Exit, or just Exit only spraying
System automatically mixes water and Chemical
to the pre-set strength depending on recommended rates from the chemical
Bio-Sparge uses either mains or farm bore hole water which is then
automatically mixed at a controlled percentage with a neutral PH chemical to
provide the disinfectant spray, Dilución / porcentajes son ajustables, but
once set, no es necesario ningún ajuste adicional. WRAC approved air gaps are
incorporated within the Bio-Sparge’s integral water tank (200 LTR) to prevent
any back flow of chemical / detergente en el suministro de agua.
Bio-Sparge SMB incorporates internal heating to protect the Bio-Sparge’s
components in cold weather together with automatic visual status alarms. These
alarms provide protection to the Bio-Sparge in the event of a loss of water
supply, o cuando se opera en condiciones de frío.
Bio-Sparge SMB is best installed on a concrete base with a camber to assist run
off and avoid puddles. When used with high volumes of traffic consideration
should be given to the drainage and storage of the run-off water. The
Bio-Sparge SMB should not be installed on soft ground, grava, or tarmac and
will not be warranted.
Precios: Starting from £8885.00 (anchura 3,6 m Standard)
LO QUE NECESITA PARA EL BIO-SMB burbujeo 160 - servicios requeridos.
380-415v, 50Hz, 3P + N + E, 16UNA, Three Phase Bio-Sparge Units
electrician should undertake the electrical installation. All electrical
components are CE Marked and the Control Cabinet wired to EN60204-1.
recommend that an RCD is fitted to the Electrical supply to the Bio-Sparge SMB.
Uso general: 30mA - 20 milisegundo, Equino, instalaciones de caballos de carreras: 30mA - 5
that a tap, or isolation valve should be installed in the water supply to the
Bio-Sparge Cabinet, to allow the water supply to be turned off for maintenance
of the Bio- SMB burbujeo.
water, o un suministro de agua de pozo, presión mínima 2 bar (29 PSI) maximum
pressure 7 bar (100 PSI).
If the water
supply is not clean then an inline filter should be fitted to ensure that only
good quality water is supplied to the Bio-Sparge SMB.
Bio-Sparge SMB incorporates back flow protection (WRAS classification ‘Type AF’
Air Gap with Circular Overflow’). However some Water Authorities may consider
that the fitment of a reduced pressure zone valve, or other ‘verifiable
backflow prevention device’ for protection against backflow in fluid category 4
o 5 es necesario. If in doubt contact your local Water Authority or a
qualified ACP (Instituto de Fontanería & Ingenieros de calefacción – Approved
QUÍMICO / DETERGENTE
recommended that a biodegradable PH neutral Chemical / Disinfectant is used
with the Bio-Sparge SMB.
your chemical supplier and ensure that the chemicals used comply with all
regulations and local bylaws.
base de hormigón
needs to be mounted on a concrete base with all of its counter parts (sensor
posts, barras de pulverización, unidad principal, etc.).
Below is a
link to a birdseye view groundworks drawing and a 3d version. tenga en cuenta el 3d
versión es la disposición típica de un pozo de absorción.